Search results

Jkswor, My seat was absolutely miserable. I looked at many high end options, but most were to wide for the given space. I wanted comfort, no vinyl (too hot and sticky in the summer), needed it to fold forward to aid access to the sink and counter and wanted arm rest. I found a wonderful seat...

Murthog, The table with leg removed or folded, rest between the two seat. The backs on the two seats, gets put on the table to make a leave bunk.

The old short shaft standards were 15” (short), 20” (long) and 25” (extra long). Of course outboard powered boats have gotten bigger and there are fewer inboard outboard boats, so now there are 30” shafts. Japan’s outboards have consistently added 2” additional inches to all of their outboards...

All of these little inflatables have the short transom. A short shaft outboard it the correct choice. As a side note, I have a few of these available that are new 2 strokes, if interested.

My experience with the Nicro solar vent has been positive. I absolutely do not want anything connected to a boat battery, then I am not on the boat. My Air Head came with the 12VDC muffin fan at the top of the vent hose... I removed it and put a 4" Marinco Nicro solar fan above the head...

I wish that I could help, but my 26 has a Honda 225 and the prop is stainless 3 x 14 1/4 x 17.

Sam, On Osprey, a wiper blade fell off and the wiper arm made a smiley face into the laminated glass. I intended to replace the glass myself, but after lots of homework, deemed it better, to pay my local glass shop to do it. The hatch on my 22 leaked and that one I took care of. It is very...

Weld Mount Fastener with 1\" Webbing

Fender Storage

Type IV PFD Storage

Weld Mount Kit

Drew, I have seen and help troubleshoot 2 C-Dory's that had water in the bow. Both boats leaked due to factory drilled holes, where the screws for the brass strip was installed. Your question is not about repair, but in both cases, as mentioned by the previous comments, there was no permanent...

Serpa4, Osprey’s Mantus anchor is 17 lbs.

PCG, When I put a new "off the shelf (from Tractor Supply) seat" in my boat, I had the same issue. I removed the rubber covering from the adjustment leaver and cut the rod back, then put the rubber leave back on, so that is was not an interference. The seat that I purchased folds forward, has...

Serpa4, Most items have been covered, but also a syringe without the needle (Kroger or other pharmacy stores usually give them to me for free), for filling the steering fluid at the helm. When I do add fluid, I put some steering fluid in a small paper cup, then using the syringe, suck a small...

Colby, Just wanted to add to comments, that my vent pipe/hose, went straight up to the overhead like yours. The compartment is so small, that it bugged me, because it was not visually pleasing to me. The hose was not really long enough to begin with, so it was almost straight, between the...

Colby, Thank you for your detailed response. I too had a conversation with the owner/designer of Airhead, when I purchased my 26. As mentioned previously, I was unwilling to keep the boat on/plugged in, when I was not on the boat. He mentioned the vent without the fan, that you have spoken...

Paul, My 2000, 22 also had no cover over the anchor locker. To cover is for aesthetics and provide some ventilation and easy access, I had my canvas maker make a simple cover that has velcro, holding it in place. The attached photo is with the cover pulled down...

Colby, Great job on the head installation! My AirHead originally had the small 12 VDC computer fan in the top of the vent line. Because I do not like to have any power on when I am not using the boat, I eliminated that and put the 4” solar Marinco fan in. There is the same vent on the bow...