Search results

Hello everybody, Thinking of getting a tow rope/line just in case I ever need it. I did just sign up for vessel assist last night but again just in case. What do you all carry if any and the ones that do, any recommendations on length, size of rope, etc. What I have read/learned so far is the...

Hello - I have noticed that my bunk boards on my trailer are scuffing up the bottom of my hull. I am pretty sure it's from where I normally launch which is by a tractor. Guessing they are not dunking the trailer deep enough for when I drive the boat on. Took it to a gelcoat repair person and...

Hello all – Getting ready to install my switch and hose connection for my washdown pump on my 19’ Angler. Is there a preferred location of these two items. Thinking the switch should be out of the cockpit so it does not get bumped and out of the elements. I will post pics when I am done but if...

Going to install a new bilge pump (Johnson ultima 1250 and new bilge hose) Have a couple questions. 1 - The old Rule 1100 strainer was either epoxied or 5200? was used to attach to hull. No screws. Dont wanna screw and instructions call for a 1/2" backing plate then screw in to backing plate...

Hello all - Looking to replace my old bilge pump (Rule 1100) with new on my 19' Angler. Any recommendations on manufactures and model numbers that are good or pumps to stay away from. Was looking at possibly going with Johnson. Will be used in saltwater a lot. Thanks everybody in advance.

My Navigation light do not work. the Nav switch lights up red but lights do not work. Bulbs look good on both sides. Could it be a bad breaker? If so does anyone know where to get those? Thanks

Sorry for all the questions. Where is the normal/best place to install my washdown pump. I was thinking above the port tank but am concerned about electrical and gas close to each other. It is going on a 19' Angler.

Installing a thru-hull fitting in the indention near the transom. Want to order parts but not sure of thickness of hull there so without drilling a pilot hole yet, does anyone know about the length of thru hull fitting I should order. I will have a 1/2" backing plate on top of the hull. Thanks

Hello - I want to install a raw water system on my 19" Angler. What system do you all use? Will be used mainly in salt water? also best location for pump install or any advice from those who have done this. Thanks

Hello, Does anyone know what is used to re-do the non-skid of a cockpit floor? Will the Kiwigrip stuff work or? Thanks

Hello all, Putting new CF numbers on my boat. What is the preferred location for these? Thanks

Hello all - I want to get my fuel hoses that lay in the spash well elevated somehow so when water gets in there and does not drain fast enough they won't be laying in water. Does anyone have any ideas or pics of maybe what they have done to keep the hoses out of water? Thanks

Hello all, I was out on my 19’ Angler yesterday and noticed one of the bottom motor mount bolts is leaking. It is a very fine leak, the sun was hitting it just right and I saw a shine. Wiped it dry and a few minutes later it was there again. My thought is I will take the nut off and bolt out...

Hello all you 19' owners. I thought I would post some pics of my install of my coaming boxes and Cannon downrigger mounts/bases I did this weekend. If you have any questions please message me and I will answer best I can. I have also replaces both tanks so can give so help on removing them. The...

Hello, I am on my second of tube of 4200 and everytime I try to use it it is already dried up at the open end and can't get any out of it. Same thing happened to me on the first tube and ended up cutting a damn hole in the body so I could use it. Ended up wasting over half the tube. Now it is...

Hello all - I have the Fusion MS-RA200 and torn between buying the gimbal mount Fusion sells or to build an enclosure and fit it in there. I will be mounting this under the shelf on my 19' C-dory. I was thinking with the gimbal mount I can take the stereo out of the boat along with all my other...

Hello, I have two 2008 Honda motors, a 90HP and a 9.9 hp. I am changing out the fuel hose assembly (primer bulb and hoses on either end). I just bought one from a local Honda dealer and the model number they sold me is 04101-zw9-010 which according to the Honda site is for 2001 or earlier...

Hello everybody - I need to remove both fuel tanks on my 08. 19' Angler. It looks like the only way to do this is to remove the flotation (?) that is mounted uner the splash well between the two tanks. It looks like it is attached with only the blow in expanded foam. Has anyone removed this? Any...

I am pretty sure I need to change my fuel pick up tubes on my 19' 2008 Angler. the tanks are Moeller. I disconnected the fuel hose, took the barbed fitting off of the pick up tube aluminum fitting then loosened the nut that holds the pick up tube to the fitting onto the tank. No luck, then...

Took boat out to lake for the first time yesterday. Went to start motor and was having hard time with both the main and kicker but finally got kicker going and later main. I believe I was having hard time getting fuel to both as the bulbs were not getting hard but finally did. I noticed debri in...