Search results

Hey gang, I purchased a Moeller 6 Gal. Topside Gas Tank a few months back. The first couple of times I used it the weather was in 80's with water temp in the 70's. This past week, we went out in the morning and everything was fine. On the way back in the air temp. was 100-101 degrees F and the...

Okay folks, I have, what appears to be a 'simple' project of relocating the two tilt lock pins up one set of holes on my 2007 Suzuki DF 50. It appears I can: Release the pressure on the power tilt and trim Tilt the engine up manually Remove the two bolts holding the lower tilt cylinder...

Hey C Brats, I'm running a 2007 Suzuki DF 50 on my CD 16. Over the past year, since adding a second battery and a few other items, I noticed my WOT rpms had dropped to approximately 5600 rpms. The Suzuki was supposed to be running from 5900 to 6500. Discovered I was running a 11 3/4 by 13 SS...

Hey Gang, Thought folks would enjoy this. Hoo Ya! Deep Sea! Water’s Edge https://vimeo.com/74585603 Director’s Cut (Video by ND1 Mariano Lorde) Hope this comes through. Be safe out there, Spuncopper

Is there anyone who is familiar with this boat (Hunky Dory)? I've seen it on the market now for over a year. It's always located in the Punta Gorda. Fl area or further south and it's always on the same trailer (which is not included). The trailer always has the same fender configuration on...

Hello: Has anyone replaced the trim sender on a Suzuki 2007 DF50TL? After researching the part I ordered a new one. It should be a fairly straight replacement, however, the old one has two leads (as shown in the manual) and the new one has four leads. I rechecked the parts number and the...

Hey Gang, Anyone have any experience with the Exide Vortex, AGM, Deep-Cycle marine batteries? Thanks.

Hey folks, Has anyone had any experience with the Sierra Marine and Drive Parts? I'm seeing more and more marine parts suppliers carrying these. There appears to be everything from oil and fuel filters to water pump kits. I'm one that believes in using OEM parts whenever possible, but Sierra...

Hey gang. I just finished changing the filter element for a Racor 120Rac-01. The element part number S3240. Basically an easy project except, the plastic element bowl would not unscrew. I figured #1. Gotta be done. So if I end up destroying the bowl it can be replaced. #2. Have some fun and see...

http://vimeo.com/81140216 Hope this comes through. Video is about 1 minute long. Hoo Yah Deep Sea! Go Navy! Go USA!

Wow Gang, A school shooting in Connecticut, Elementry school, K-4. Last report 18 children dead, 8 adults. What is going on in this country?

Hey Gang, Has anyone had experience with the Hummingbird 798ci SI Combo (or similar unit)? I am planning on using it in freshwater to search for historic sites flooded out when the Lake Wateree dam was built in the early 1900's. This lake is in SC. I'm especially interested in the side scan...

Hey Gang: I have read several posts that concern storage or seating for a CD 16. I built a wood frame that holds two milk crates. I use them to stow my river anchors. It will also hold a 48 quart cooler. I used plywood to make the tops and coated them with non-skid. Add boat cushions and it...

Hey again Folks! :lol: Someone on C-Brat's website is on the ball and removed the phishing posts!! Good job gang! :D

One more thing Folks: Do not respond to these phishing posts. They will then have your e-mail address and can flood you with junk e-mails.

Hey Folks: From the list of latest posts it would appear that C-Brats has had a major phishing attack. :crook Be careful. We're from South Carolina and if you've been following the news South Carolina has had a major hack attack on the Dept. of Revenue that is going to cost us millions...

Hey Folks: The craftsman among you probably already know this tip, but for others it may help. I recently did a small project that required just a dap of 3M 4200 fast cure. I purchased the smallest tube I could find. To my dismay the directions said it had to be used within 48 hours of opening...

Hey Folks! :D My wife of forty-one years (and counting) has informed me that she didn't practicularly like the name I chose for our CD 16, "Yare". She said it was hard to pronounce correctly and sounded horrible on the radio, since people couldn't pronounce it correctly. Well, the boat...

Hey Gang, :D I just finished a project on my CD16. Part of the project required laying out scribe lines on finished/polished material. Of course no one wants to scratch lines on pretty polished or finished material. I used the painter's tape and laid out my scribe lines on the tape. I then...

Hey Gang, 8) The motorwell boot on my CD 16 is beyond shot. I know it is a 4 1/2 inch boot, but I can only find replacement boots that have 8 mounting holes, mine has 6. Sooo... which manufacture is mounted on my CD 16 or was it left to the discretion of the dealer who prepped the boat...