trim tilt annotated

trim tilt annotated

  • Media owner Sunbeam
  • Date added Aug 25, 2013
  • Reaction score 0
  • Comments 0

  • Media owner Sunbeam
  • Date added Aug 25, 2013
  • Reaction score 0
  • Comments 0
Wondering where to check fluid level for trim/tilt system.

Wondering where to check fluid level for trim/tilt system.

  • Media owner Sunbeam
  • Date added Aug 25, 2013
  • Reaction score 0
  • Comments 0
Photo deliberately edited to be over exposed, showing Honda/Mini-Jacker/trim tab relationship.

Photo deliberately edited to be over exposed, showing Honda/Mini-Jacker/trim tab relationship.

  • Media owner Sunbeam
  • Date added Aug 17, 2013
  • Reaction score 0
  • Comments 0
Diagram with notes after job done.

Diagram with notes after job done.

  • Media owner Sunbeam
  • Date added Aug 4, 2013
  • Reaction score 0
  • Comments 0

  • Media owner Sunbeam
  • Date added Aug 3, 2013
  • Reaction score 0
  • Comments 0

  • Media owner Sunbeam
  • Date added Aug 3, 2013
  • Reaction score 0
  • Comments 0

  • Media owner Sunbeam
  • Date added Aug 3, 2013
  • Reaction score 0
  • Comments 0
Diagram intake

Diagram intake

  • Media owner Sunbeam
  • Date added Aug 3, 2013
  • Reaction score 0
  • Comments 0
Diagram electrical 1 (rectifier)

Diagram electrical 1 (rectifier)

  • Media owner Sunbeam
  • Date added Aug 3, 2013
  • Reaction score 0
  • Comments 0
Yamaha filter

Yamaha filter

  • Media owner Sunbeam
  • Date added Mar 12, 2013
  • Reaction score 0
  • Comments 0

  • Media owner Sunbeam
  • Date added Mar 10, 2013
  • Reaction score 0
  • Comments 0
New wedge in place, viewed from port side.

New wedge in place, viewed from port side.

  • Media owner Sunbeam
  • Date added Dec 8, 2012
  • Reaction score 0
  • Comments 0
Lowered into position, seen from beneath. If this works well I'll do something more elegant than the tape to hold the rubber in place (when not on the road!).

Lowered into position, seen from beneath. If this works well I'll do something more elegant than the tape to hold the rubber in place (when not on the road!).

  • Media owner Sunbeam
  • Date added Dec 8, 2012
  • Reaction score 0
  • Comments 0
Taped some dense rubber stripping onto the top (the tape is just to hold it in place while the motor comes down, so I don't have to have my fingers in there).

Taped some dense rubber stripping onto the top (the tape is just to hold it in place while the motor comes down, so I don't have to have my fingers in there).

  • Media owner Sunbeam
  • Date added Dec 8, 2012
  • Reaction score 0
  • Comments 0
Made a new wedge out of materials I had with me on the road (1" x 2" scrap, planed top edge at 45? to contact motor better than the original, "sharp" edge).

Made a new wedge out of materials I had with me on the road (1" x 2" scrap, planed top edge at 45? to contact motor better than the original, "sharp" edge).

  • Media owner Sunbeam
  • Date added Dec 8, 2012
  • Reaction score 0
  • Comments 0
It's now permanently deformed.

It's now permanently deformed.

  • Media owner Sunbeam
  • Date added Dec 8, 2012
  • Reaction score 0
  • Comments 0
You can see a "slot" cast into the boat side of the motor mount toward the upper right. There is one of these each side and my new "wedge" fits into them.

You can see a "slot" cast into the boat side of the motor mount toward the upper right. There is one of these each side and my new "wedge" fits into them.

  • Media owner Sunbeam
  • Date added Dec 8, 2012
  • Reaction score 0
  • Comments 0
M-Y Wedge slipped out of place and deformed, not sure why (did work fine for a different 3,000-mile tow). This allowed the motor to come down somewhat, but luckily not all the way as it "wedged" between the tilt cylinder and the transom.

M-Y Wedge slipped out of place and deformed, not sure why (did work fine for a different 3,000-mile tow). This allowed the motor to come down somewhat, but luckily not all the way as it "wedged" between the tilt cylinder and the transom.

  • Media owner Sunbeam
  • Date added Dec 8, 2012
  • Reaction score 0
  • Comments 0
S

M-Y Wedge slipped out of place and deformed, not sure why (did work fine for a different 3,000-mile tow). This allowed the motor to come down somewhat, but luckily not all the way as it "wedged" between the tilt cylinder and the transom.

  • Items 43
  • Album owner Sunbeam
  • Date created
There are no comments to display.

Album information

Category
Yamaha F80, Honda 8D, Mercury 5
Album owner
Sunbeam
Date created
Item count
43
View count
2,902
Comment count
0
Rating
0.00 star(s) 0 ratings

Album privacy

S

Sunbeam

Media items
504
Albums
30
Can view media items
Inherited from category
Can add media items
Album owner only

Share this album

Back
Top