Recent content by Chica

My lowrance LC113 quite working. The Lowrance company, withour seeing it said it was not repairable. My Lowrance LC113 quit working. The tech. support for the company said it can not be repaired. Even though the unit is 6 or 7 years old it has had limited use. I am sure they want me...

My pump is is in the aft sump, I have a switch in the cabin and aside in the splash well, aft. I have both manual and automatic switchs. I was thinking of adding a manual pump. The bilge is never dry. Tried a check valve and was not happy with that. I have two Rule pumps in the sump, GPM?, boat...

Adding a manual bilge pump that is. Chica

Have been out of the loop for a while. Not real happy with the bilge area and my Rule bilge pump on my 22' Angler. Switchs always seem to be a problem, whether on auto or manual. Have considered adding a manual. Any thoughts? Thanxs Chica

Breausaw, if you contact C Dory they will send you a new sticker for your boat which states it is rated for 115hp. Chica

I have an E-tec 115 hp on my 22'ft angler and love it. Runs 28-30 mph at 4600 rpm's. It weighs 8 pounds more than a Honda 90 and lots more "soup". Chica

I have an E-tec 115 on my angler and really like it. No smoke, faster, and as quite as my Honda 90. I use a gallon of HD100 to every 100 gallons of fuel. It weighs about 6 pounds more than my Honda 90. I run 29-31 mph at 4150 rpm's. I fished it eveyday for 5 weeks this summer and have had no...

I must have gotten some of the same batch of flurocarbon leader you had-no more for me after several breaks this season. Chica

Which epoxy are you using to fill the drilled out, undercut holes? The marine -tex I have is not suitable for use in a syringe and some epoxies have a warning in the small print,"Not for prolonged immersion in water" ie, loctite's extra time epoxy. I like the idea of filling with a syringe and...

Earlier this year I put an E-Tec on my 22' angler. I started with a 19 pitch prop but was unable to reach the recommended 5500-6000 RPM's and a switch to 17 pitch did not get me there either. Next year I'll try a 15 pitch, "Thanks Coop's Cruiser". At 4150 rpm's I run at 29-31 mph, fast enough...

Hello Joel, please put me down for two covers, in the color that matches our gelcoat. Mailing address: Robert Nehls 166 Lyndale Lane Butte,MT 59701 How would you like to be paid, presonal check or money order? My home e-mail is...

I exchanged my Honda for a 115 E-tec, this is on a 22' angler which is heavy with gear and crew. I ran it at sea level and had the factory reccommended 19 pitch prop. At WOT it turned 5100 RPM's with a top speed of 35 mph. I have trim tabs and a paratrim (sp). Running at 29mph was fine, but...

Grumpy, thank you for the information. The part number is 1025 and I found it in two locations. Shaped like a T and bolts vertical to the side of the gunnel. Thanxs again, Chica

Wondering where those with a 22' crusier or angler placed the base plate for a Brutus puller. I have Penn downriggers and a Scotty base is necessary for the Brutus, which does not fit the gunnel. I was looking at the area aft of the lazaret (sp). Suggestions. Thanxs, Chica

Thank you all for the imput. I'm looking at Suzuki 115, Yamaha 115, and now a new player,E-Tec 115. Like Suzuki, but the closest dealer is 350 miles, and we all know "Murphy's Rule". E-Tec and Yamaha dealer is 60 miles away-and no mountain passes. This is worse than buying a new car! C-Dory...