Recent content by SEdowneast

  1. S

    Boat Lift Bunk Input

    Hi Bob! I agree with you completely about articulated bunks! I'd love to find those type brackets that would fit on my beams and go that route. Unfortunately, I've looked a lot and have been unable to do so. Thus, I am afraid I will have to live with the fixed brackets and vertical lumber...
  2. S

    Boat Lift Bunk Input

    Hello fellow C Brats. I was looking for some input from those who keep their C Dory's on a boat lift. I keep my Venture 23 on a lift with two bunks where the lumber is set on flat edge with a 7-8 degree angle that has been ripped into the lumber to accommodate the increasing dead rise from...
  3. S

    Venting heat

    Thought I would chime in here. I'm in SC and it is the normal summer brutal heat here. I've got a 23 Venture. When not in use, my boat is on a lift with a full Angola Cover on it, but I have added cover vents that I think do help keep the heat down. I've got a remote temp & humidity gauge...
  4. S

    I need an outdoor cover

    Another recommendation for Angola! They made a cover for my new 23 Venture. Just outstanding!!
  5. S

    Must bunks align with stern when on a boat lift

    I was always under the impression that the lifting points for these boats should be around the drivers seat forward and slightly forward of the stern in the rear. Thus, the I beams of the lift should be located in the same area for the boat to be centered. Depending on the width of the cradle...
  6. S

    Angola Canvas Covers for C Dory

    Hi Bob! I had Angola add 28 inches to the sides, which was the same as someone else who posted here had done. I think that's about right since it covers the entire sides. On the port side, I also have two bungees at the stern area that also clip to eye bolts mounted into the sides of the...
  7. S

    Angola Canvas Covers for C Dory

    Just a shout out to Angola Canvas from Indiana for making a very nice Sunbrella cover for my new Venture 23. They already had the measurements/plan and I added to the length of the sides plus a few other things which they easily handled. The quality of the work is outstanding and the cover...
  8. S

    Need Help with Venture 23 Boat Lift Bunk Specs/Hull Deadrise

    Thanks Bob, I think I’ll follow your advice! One average angle for the duration of the bunk sounds like the way to go and certainly the simplest! I too agree that the hull of this boat is strong and should be well supported using this method. All great info and very much appreciated!!
  9. S

    Need Help with Venture 23 Boat Lift Bunk Specs/Hull Deadrise

    Thataway, my apologies! From your post it didn't seem to me that you would have considered a circular saw as an option. Thus, I was just outlining the process I go through. Your experience with all this certainly stands out to me, as your description about how to do it with a circular saw is...
  10. S

    Need Help with Venture 23 Boat Lift Bunk Specs/Hull Deadrise

    Thataway, I use a circular saw and do the ripping of the board as its laying on its side. The saw can be adjusted for angle of cut and has a gauge so you know what the angles are. Of course the blade is 90 degrees when straight up but the angle decreases as the blade lays down and the base...
  11. S

    Need Help with Venture 23 Boat Lift Bunk Specs/Hull Deadrise

    Such great folks and valuable insight on this forum!! So appreciate it! For my boat lift I will basically rip the bunk boards with a circular saw at the required angles. The boards stand up attached to the beam brackets. Not really hard to do as long as you know what angles to cut.
  12. S

    Need Help with Venture 23 Boat Lift Bunk Specs/Hull Deadrise

    Well since the deadrise of this boat progresses from somewhat flat, say 6 degrees at the stern, to much more towards the bow, I generally bevel the edges of the wood bunks to similar angles. By doing so the boat will sit flat and is fully supported by the entire portion of the edge not just...
  13. S

    Need Help with Venture 23 Boat Lift Bunk Specs/Hull Deadrise

    I have asked the questions via the dealer but haven’t gotten a response yet. I think they are quite busy these days! Thinking someone on here might have already been down this road, this my post. Thanks!
  14. S

    Need Help with Venture 23 Boat Lift Bunk Specs/Hull Deadrise

    Hello Everyone, well I guess I will be part of the group in earnest soon, as we’ve just ordered a new Venture 23. Very excited about the adventures ahead!! I will need to get my boat lift bunks built for the new boat and am looking for the specs for them. If anyone with a Venture 23 could...
  15. S

    Any Venture 23 owners in SC, NC or Ga?

    Hello All! New member and first post!! I am considering purchasing a Venture 23 but would like to see one in person without driving all the way to west coast of Florida. I am located in Columbia, SC area. Is there anyone in SC, NC, or Ga who would be willing to let me and my wife come take a...
Back
Top